Plumber's Essentials: What You Need for Bathtub Installation
Plumber's Essentials: What You Need for Bathtub Installation
Blog Article
What are your opinions about Installing A Bathtub?
Installing a bath tub isn't precisely brain surgery, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a new one is likewise a moderately challenging project. If the old tub is readily accessible, the project can relocate easily; if you need to open up a wall to remove the old bathtub and also place the new bathtub, the job is a lot harder. In either case, the job is within a house handyman's skills, although you will certainly require a helper to move out the old tub and set in the new one. Ensure you have actually qualified on your own for the task and are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is better to think about utilizing one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This post will certainly assist you install a brand-new tub in your restroom if you have currently acquired a brand-new tub and do not require to alter the arrangement of your previous supply of water pipes.
Your devices and also material checklist need to comprise the following:
Preparing for the Setup
To start with, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps device to stop pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final setting.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, then the first thing you should do is detach the water. After doing so, activate the taps to drain any kind of water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic because of the restricted gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. When the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to going on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the needed setting. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the level and also adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit all-time low of the furthest versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the water and also inspect all joints and also new pipework for leaks and tighten them if necessary. Fill the tub and additionally inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling and sealing around the bathtub should wait till the bath tub has actually been made use of at the very least when as this will resolve it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers are in place in between the faucet as well as the sink. Safeguard the faucet in place with the maker given backnut. When the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap ports. The previous type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to break a stiff seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your components and also installations. They are offered in tubes and cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealer can split rather early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been introduced to that article on A Step-by-Step Guide to Installing a Bathtub from a friend on a different site. For those who enjoyed our post if you please make sure you remember to pass it around. We truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
For fast action, contact! Report this page